lu.ca/calc/

Bolt pattern 3D

Export
?

Drag an arrow tip to change a load; it snaps to the axes and diagonals (hold Alt to stop it). Drag the open circle at its foot to move where it acts; the bar from the bracket follows. Shift drags straight up or down.

Drag a bolt to move it in its face; Shift moves it along its axis. Click a bolt, then drag the knob on its axis to tilt it. Shift-click selects several.

Arrow keys nudge the selection (Page Up/Down along the axis), F flips the axis, ⌘D duplicates, Delete removes.

Drag empty space to orbit; double-click resets the view. Click x, y or z in the corner to look along that axis.

Bolt types

size, grade and torque; preload range from αA

Bolts

point in the joint interface · axis = direction in which the joint opens, e.g. +z or 0.7, 0, 0.7

Loads

points in global x, y, z · moments act anywhere

Paste straight from Excel, Sheets or a CSV: click a cell and press ⌘V / Ctrl+V. Headers like x, z [mm], axis (+z or 0.7, 0, 0.7), nx ny nz, Fz (kN) or Name are recognised and units converted. Without headers, bolts read x, y, z (and nx, ny, nz), loads x, y, z, Fx, Fy, Fz.

Margins per bolt

MS = allowable ÷ (FS × actual) − 1. Zero or more passes. Click a row to select the bolt; hover a margin to see how it fails.

Faces

bolts with parallel axes in one plane share a flange · reaction = what the supports push on the part

Calculation

Assumptions and sources

Assumptions

  • The clamped part is a rigid body on elastic bolts. Each bolt location has an axial stiffness ka along its own axis (bolt plus clamped body, VDI 2230 §5.1, as in the 2D tool) and a shear stiffness ks across it, set by the ratio ks/ka in the Stiffness tab and scaled by bolt area. Six equilibrium equations, three forces and three moments about the bolt centroid, give the part's translation and rotation, and from them the load on every bolt.
  • With all bolt axes parallel the result is exactly the 2D rigid-flange bolt group (checked in the test suite). When faces meet at an angle, the split of shear between faces depends on ks/ka: before slip, friction makes a joint about as stiff across as along (≈ 1); once it slips into bearing it is far softer across (Huth's formula gives about 0.1–0.3 for steel). The page shows how much the answer moves when the ratio is halved.
  • Each bolt is then checked as in the 2D tool: separation, slip, bolt yield, bearing and fatigue after VDI 2230-1 R7–R12. The edge-opening check runs per face, on that face's minimum-plate outline, using the face's linear field of axial bolt load from the rigid-body motion.
  • One clamped stack for every bolt (the first plate is the bracket, the rest is what it bolts to). Not modelled: prying, contact between faces (the joint is assumed closed), plate bending, thermal load, thread stripping. A moment the bolts cannot react, for example about a line through all of them, is reported and the checks it affects are shown as failed.
  • The drawing is to scale: faces are the minimum plate around each face's bolts (AISC 360-16 J3.4, EN 1993-1-8 Table 3.3), joined where faces meet; the deformed view exaggerates the computed rigid-body motion by the factor shown.

Sources

  1. VDI 2230 Part 1:2015-11. Systematic calculation of highly stressed bolted joints — Joints with one cylindrical bolt. VDI / Beuth. Steps R0–R13, compliances §5.1, embedding §5.4.
  2. ISO 898-1:2013. Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1. Strengths and stress area As.
  3. SAE J429. Mechanical and Material Requirements for Externally Threaded Fasteners. Grades 5 and 8.
  4. ISO 3506-1:2020. Corrosion-resistant stainless steel fasteners — Part 1. A2-70, A4-80.
  5. ISO 261, ISO 724 and ISO 68-1. ISO general purpose metric screw threads. Coarse and fine series, d2, d3.
  6. ASME B1.1-2019. Unified Inch Screw Threads. UNC and UNF series; As = π/4·(d − 0.9743/n)².
  7. ISO 4014, ISO 273, ISO 7089, ASME B18.2.1, ASME B18.2.8, ASTM F436. Head bearing diameter dW, clearance holes dh, hardened washers.
  8. Budynas and Nisbett. Shigley's Mechanical Engineering Design, 11th ed., McGraw-Hill, 2020, ch. 8. Joint stiffness, shear joints with eccentric load.
  9. Bickford. Introduction to the Design and Behavior of Bolted Joints, 4th ed., CRC Press, 2008. Joint diagrams, separation.
  10. ECSS-E-HB-32-23A (2010). Threaded fasteners handbook. ESA. Bolt-group loads, margins of safety.
  11. ISO 16047:2005. Fasteners — Torque/clamp force testing. Friction coefficients μG, μK.
  12. AISC 360-16. Specification for Structural Steel Buildings. §J3.3 minimum spacing, Table J3.4 / J3.4M minimum edge distance.
  13. EN 1993-1-8:2005. Eurocode 3 — Design of joints. Table 3.3, minimum end, edge distances and spacing.
  14. Huth, H. Influence of fastener flexibility on the prediction of load transfer and fatigue life for multiple-row joints. In: Fatigue in Mechanically Fastened Composite and Metallic Joints, ASTM STP 927, ASTM, 1986, pp. 221–250. Shear flexibility of a bolted joint in bearing. Secondary: the equation as reproduced in Lin, JAMS / AMTAS slides (Univ. of Washington) and the constants a = 2/3, b = 3.0 for bolted metal from Altair Inspire 2024 help, flexible fasteners; both accessed 18 October 2026. Variants in the literature differ only in double shear; this page uses single shear (n = 1), where they agree. Not checked against the original paper.
  15. ISO/TR 16224:2012. Technical aspects of nut design. Alexander's method for thread stripping, as implemented in the thread engagement tool (its own sources list cites FED-STD-H28/2B, ISO 965 and ASME B1.1 for the thread limits and shear areas).

For design studies. Check results against the full VDI 2230 procedure before relying on them.

Recommended bolts